$49 AC Tune-Up — Book your tune-up today
Mon–Fri 8:00am–5:00pm · 24/7 Emergency Service
Fast AC Repair Co — The hotter you are, the faster we come Book Online
Services
AC Repair & DiagnosticsAC Installation & ReplacementAC Maintenance & Tune-UpsDuctwork Design & RepairDuct CleaningMini-Split SystemsIndoor Air QualityPlumbingSeptic Services
Service Areas
Fort PiercePort St. LucieVero BeachJensen Beach All Service Areas
Company
About Us Reviews Case Studies Blog FAQ Contact Book Online

Home · Services · Ductwork

Ductwork Design & Repair

Designed, fabricated, and repaired in-house — because great AC starts with great airflow.

The Service

Your AC is only as good as the ducts delivering the air

Leaky, crushed, or undersized ductwork can waste a big share of the cooling you pay for — and leave some rooms hot no matter what the thermostat says. We design duct systems properly, repair the ones that are failing, and fabricate sheet metal in-house, so the fit is right and the job doesn't wait on anyone else.

Whether it's a new build, a remodel, or a house where one bedroom never cools down, we find the airflow problem and fix it at the source.

  • Complete ductwork design for new construction and remodels
  • Duct repair and replacement for damaged or leaking runs
  • In-house sheet metal fabrication for exact fits
  • Airflow balancing for rooms that run hot or cold
  • Ductwork for AC package units and system replacements
Call (772) 678-6676
Dust and debris buildup inside ductwork, photographed from inside the duct
What we find inside older ductwork: dust and debris buildup coating the duct board.
New galvanized duct run being installed in a block building under construction, with scaffolding below
And the other end of the job: a brand-new galvanized duct run going in on a new-construction build.
A custom duct board trunk section fabricated on the floor of a home under construction, foil tape and tools sitting on top of it
Custom ductwork, fabricated on site: a duct board trunk section built on the floor of a home under construction, foil tape and tools on top.
Wide interior of a home under construction with wood trusses, insulated flex duct runs in the ceiling, ladders and duct collars on the floor
A whole-home rough-in in progress: insulated flex duct runs in the ceiling trusses, ladders up, and duct collars staged on the floor.
Metal vent pipe set plumb through rebar and formwork in new construction, a level strapped to the pipe
Set plumb before the pour: a metal vent pipe through rebar and formwork in new construction, a level strapped to the pipe to check it.
Metal duct boot installed in the ceiling trusses of a home under construction, metal stud framing below and a worker in the background
New-construction rough-in: a metal duct boot set in the ceiling trusses, metal stud framing below and a crew member at work in the background.
Bags of R6 flex duct staged inside a framed home under construction, ready for the duct rough-in
Ready for the rough-in: bags of R6 flex duct staged inside a framed home under construction.
Several foil-faced ductboard plenum sections fabricated in the Fast AC Repair shop, standing on the concrete floor
Fabricated in our own shop: foil-faced ductboard plenum sections standing on the shop floor, ready to go out on a job.
Two Fast AC Repair crew members carrying a tall fabricated ductboard section through the warehouse, boxed wall-mount air handlers stacked nearby
Two of our crew carrying a tall fabricated ductboard section through the warehouse, boxed wall-mount air handlers stacked nearby.
Top-down view of a ductboard elbow fitting being fabricated on a plywood work deck, a large insulated flex duct run above it
From above: a ductboard elbow fitting being fabricated on a plywood work deck, a large insulated flex run overhead.
A foil-faced ductboard duct run laid out on a plywood deck against a block wall, with insulated flex duct overhead
A ductboard run in place: foil-faced ductboard sections on the plywood deck, flex duct overhead.
Bags of R6 flex duct staged inside a home under construction with metal stud framing, ready for the duct rough-in
Staged for the rough-in: bags of R6 flex duct inside a framed home under construction.
Galvanized duct pipe and stacked elbow fittings on the shop shelves, with labeled bins of copper fittings below
Duct fittings on the shelf back at the shop: galvanized pipe and stacked elbows up top, bins of copper fittings below.

Warning Signs

Signs you need ductwork design & repair

  • One or two rooms never reach the set temperature
  • You can hear whistling or rattling from the vents
  • Dust builds up unusually fast around the house
  • Visible damage, sagging, or disconnected ducts in the attic
  • High electric bills with a system that checks out fine
  • A remodel or addition needs air delivered to new space

How It Works

How a job runs

1

We inspect the system

We look at the duct layout, condition, and airflow to find where air is being lost or choked off.

2

We design the fix

You get a clear plan — repair, partial replacement, or a new design — based on what your home actually needs.

3

We fabricate & install

Sheet metal is fabricated in-house for an exact fit, then installed and sealed by our own crew.

4

We balance the air

We test airflow room by room so the whole house cools evenly.

FAQ

Questions homeowners ask us

Usually it's the ductwork: a long or undersized run, a leak, or poor balancing starves that room of air. The AC itself is often fine — the delivery is the problem, and it's fixable.

Yes. We fabricate sheet metal in-house, which means custom pieces fit right and jobs don't stall waiting on outside suppliers.

Absolutely — new construction HVAC design, including the full duct system, is one of our core services.

Hot rooms, high bills, excess dust, and visible attic damage are the classic signs. An inspection settles it — we'll show you what we find.

Call Now Request Callback